manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 201 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 201

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 201

Description

This command specifies the network-queue policy which defines queue parameters such as CBS, 
high priority only burst size, MBS, CIR and PIR rates, as well as forwarding-class to queue 
mappings. The network-queue policy is defined in the 

config>qos>network-queue

 context.

Default

default

Parameters

name — 

Specifies an exisiting network-queue policy name.

resv-cbs

Syntax

resv-cbs 

percent-or-default

no resv-cbs

Context

config>card>mda>access>egress
config>card>mda>access>ingress
config>card>mda>network>egress
config>card>mda>network>ingress
config>port>access>egress>pool
config>port>access>egress>channel>pool
config>port>access>ingress>pool
config>port>network>egress>pool

Description

This command defines the percentage or specifies the sum of the pool buffers that are used as a 
guideline for CBS calculations for access and network ingress and egress queues. Two actions are 
accomplished by this command.

• A reference point is established to compare the currently assigned (provisioned) total CBS with 

the amount the buffer pool considers to be reserved. Based on the percentage of the pool reserved 
that has been provisioned, the over provisioning factor can be calculated.

•  The size of the shared portion of the buffer pool is indirectly established. The shared size is 

important to the calculation of the instantaneous-shared-buffer-utilization and the average-
shared-buffer-utilization variables used in Random Early Detection (RED) per packet slope plot-
ting.

It is important to note that this command does not actually set aside buffers within the buffer pool for 
CBS reservation. The CBS value per queue only determines the point at which enqueuing packets are 
subject to a RED slope. Oversubscription of CBS could result in a queue operating within its CBS 
size and still not able to enqueue a packet due to unavailable buffers. The resv-cbs parameter can be 
changed at any time. 

If the total pool size is 10 MB and the resv-cbs set to 5, the ’reserved size’ is 500 KB.

The 

no

 form of this command restores the default value.

Default

default (30%)

Parameters

percent-or-default — 

Specifies the pool buffer size percentage.

Values

0 — 100, default

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments