manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 200 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 200

Configuration Commands

Page 200

7750 SR OS Interface Configuration Guide

ingress

Syntax

ingress 

Context

config>card>mda>access
config>card>mda>network
config>port>access

Description

This command enables the context to configure ingress buffer pool parameters which define the 
percentage of the pool buffers that are used for CBS calculations and specify the slope policy that is 
configured in the 

config>qos>slope-policy

 context.

On the MDA level, access ingress pools are only allocated on channelized MDAs. 

pool

Syntax

[

no

] 

pool 

[

name

]

Context

config>card>mda>access>egress
config>card>mda>access>ingress
config>card>mda>network>egress
config>port>access>egress
config>port>access>ingress
config>port>network>egress
config>port>network>egress

Description

This command configures MDA access egress/ingress and network egress/ingress pool policies. 

On the MDA level, access and network egress and access ingress pools are only allocated on 
channelized MDAs. On the MDA level, access and network egress and access ingress pools are only 
allocated on channelized MDAs. Network ingress pools are allocated on the MDA level for non-
channelized MDAs.

Default

default

Parameters

name — 

Specifies the pool name, a string up to 32 characters long composed of printable, 7-bit 

ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string 
must be enclosed within double quotes.

queue-policy

Syntax

queue-policy 

name

no queue-policy

Context

config>card>mda>network>ingress
config>port>sonet-sdh>path>network

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments