manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 194 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 194

Configuration Commands

Page 194

7750 SR OS Interface Configuration Guide

Parameters

alarm — 

Enables event generation if the MDA is required to share an MSFP with another MDA that 

is in a different group. MDAs within the same group sharing an MSFP will not cause this alarm.

group 

group-id

 — 

Specifies the logical MSFP group for the MDA. MDAs configured with the same 

group-id

 will be placed on the same MSFP. 

Values

0 — 32 (A value of 0 removes the MDA from the group.)

Default

By default, “none” is used, and the system will attempt to assign a unique MSFP to 
the MDA.

egress

Syntax

egress

Context

config>card>mda

Description

This command enables the context to configure egress MDA parameters.

ingress

Syntax

ingress

Context

config>card>mda

Description

This command enables the context to configure ingress MDA parameters.

hsmda-pool-policy

Syntax

hsmda-pool-policy 

policy-name

no hsmda-pool-policy

Context

config>card>mda>egress
config>card>mda>ingress

This command specifies an HSMDA buffer pool policy. The policy may be assigned to an ingress or 
egress HSMDA. The policy contains the needed commands to provision the behavior for the class 
and root buffer pools on an HSDMA. The policy may be applied using the hsmda-pool-policy 
command within the config card slot-id mda mda-number ingress or config card slot-id mda mda-
number egress contexts. When applied at ingress, the policy manages the ingress HSMDA buffer 
pools. The egress context manages the egress HSMDA buffer pools.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments