manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 191

All parameters in the MDA context remain and if non-default values are required then their 
configuration remains as it is on all existing MDAs.

The 

no

 form of this command deletes the MDA from the configuration. The MDA must be 

administratively shut down before it can be deleted from the configuration. 

Default

No MDA types are configured for any slots by default.

Parameters

mda-type — 

The type of MDA selected for the slot postion. 

7750:

 m60-10/100eth-tx, m10-1gb-sfp, m16-oc12/3-sfp, m8-oc12/3-sfp, m16-oc3-sfp, m8-oc3-

sfp, m4-oc48-sfp, m1-oc192, m5-1gb-sfp, m12-chds3, m1-choc12-sfp, m1-10gb, m4-choc3-sfp, 
m2-oc48-sfp, m20-100eth-sfp, m20-1gb-tx, m2-10gb-xfp, m4-atmoc12/3-sfp, m16-atmoc3-sfp, 
m20-1gb-sfp, m4-chds3, m1-10gb-xfp, vsm-cca, m5-1gb-sfp-b, m10-1gb-sfp-b, m4-choc3-as-
sfp, m10-1gb+1-10gb, isa-ipsec, m1-choc12-as-sfp, m12-chds3-as, m4-chds3-as, isa-aa, m10-
1gb-hs-sfp, m1-choc3-ces-sfp, m4-10gb-xp-xfp, m2-10gb-xp-xfp, m20-1gb-xp-sfp, m20-1gb-
xp-tx, imm24-1gb-sfp, imm24-1gb-tx, imm4-10gb-xfp, imm2-10gb-xfp

7710

: m60-10/100eth-tx, m8-oc3-sfp, m5-1gb-sfp, m2-oc48-sfp, m20-100eth-sfp, m20-1gb-tx, 

m4-atmoc12/3-sfp, m20-1gb-sfp, m5-1gb-sfp-b, m4-choc3-as-sfp, c8-10/100eth-tx, c1-1gb-sfp, 
c8-chds1, c4-ds3, c2-oc12/3-sfp, c8-atmds1, c1-choc3-ces-sfp, m1-choc12-as-sfp, m12-chds3-
as, m4-chds3-as, m20-1gb-xp-sfp, m20-1gb-xp-tx

7450:

 m60-10/100eth-tx, m10-1gb-sfp, m16-oc12/3-sfp, m8-oc12/3-sfp, m16-oc3-sfp, m4-oc48-

sfp, m1-10gb, m2-oc48-sfp, m20-100eth-sfp, m20-1gb-tx, m2-10gb-xfp, m20-1gb-sfp, m1-
10gb-xfp, vsm-cca, m10-1gb-sfp-b, m10-1gb+1-10gb, m10-1gb-hs-sfp, m4-10gb-xp-xfp, m2-
10gb-xp-xfp, m20-1gb-xp-sfp, m20-1gb-xp-tx, imm24-1gb-sfp, imm24-1gb-tx, imm4-10gb-xfp, 
imm2-10gb-xfp

named-pool-mode

Syntax

named-pool-mode

Context

config>card>mda
config>port

Description

The named-pool-mode CLI context is used to store the MDA and port level named pool mode 
configuration commands. Currently, only the ingress and egress named-pool-policy commands are 
supported. Any future named pool mode configuration commands or overrides will be placed in the 
named-pool-mode CLI context. Within the context is an ingress and egress context.

Enter the named-pool-mode to define the ingress and egress named pool policy associations for either 
an MDA or port. The node may be entered regardless of the current named-pool-mode state of the 

IOM.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Watchguard Firebox T15 Quick Start Manual preview
Firebox T15
Brand: Watchguard Pages: 39
Zhone 6211 Product Manual preview
6211
Brand: Zhone Pages: 7
Zhone 6211 Quick Installation Instructions preview
6211
Brand: Zhone Pages: 1
D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network... User Manual preview
DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...
Brand: D-Link Pages: 53
FOR-A MFR-4000 Operation Manual preview
MFR-4000
Brand: FOR-A Pages: 72
Allied Telesis AT-8000C Declaration Of Conformity preview
AT-8000C
Brand: Allied Telesis Pages: 1
Maipu MP2900-04-AC Installation Manual preview
MP2900-04-AC
Brand: Maipu Pages: 80
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
WAGO 852-1411 Operating And Assembly Instructions preview
852-1411
Brand: WAGO Pages: 2
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Planet WNAP-7335 Quick Installation Manual preview
WNAP-7335
Brand: Planet Pages: 2
Cayman Systems 2E-H-W User Manual preview
2E-H-W
Brand: Cayman Systems Pages: 170
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4
ZyXEL Communications GS-1116A Supplementary Manual preview
GS-1116A
Brand: ZyXEL Communications Pages: 1
LevelOne GNC-0112 Quick Installation Manual preview
GNC-0112
Brand: LevelOne Pages: 10
Tachosys digiDL-B Administration Manual preview
digiDL-B
Brand: Tachosys Pages: 15

Brands by name

Popular brands

Load more brands