manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 155 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 155

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 155

Configuring LAG Parameters

LAG configurations should include at least two ports. Other considerations include:

•

A maximum of eight ports can be included in a LAG. All ports in the LAG must share the 
same characteristics (speed, duplex, hold-timer, etc.). The port characteristics are 
inherited from the primary port.

•

Autonegotiation must be disabled or set limited mode for ports that are part of a LAG to 
guarantee a specific port speed.

•

Ports in a LAG must be configured as full duplex.

The following example displays LAG configuration output:

A:ALA-A>config>lag# info detail

----------------------------------------------

        description "LAG2"

        mac 04:68:ff:00:00:01

        port  1/1/1

        port  1/3/1

        port  1/5/1

        port  1/7/1

        port  1/9/1

        dynamic-cost

        port-threshold 4 action down

----------------------------------------------

A:ALA-A>config>lag#

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments