manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 101 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 101

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 101

Basic Configuration

The most basic configuration must have the following:

•

Identify chassis slot.

•

Specify line card type (must be an allowed card type).

•

Identify MDA slot.

•

Specify MDA type (must be an allowed MDA type).

•

Identify specific port to configure.

The following example displays some card configurations:

ALA-A>config# info

. . .

#------------------------------------------

# Card Configuration

#------------------------------------------

card 1

        card-type iom-20g

        mda 1

            mda-type m60-10/100eth-tx

        exit

        mda 2

            mda-type m60-10/100eth-tx

        exit

    exit

    card 2

        card-type iom-20g

        mda 1

            mda-type m10-1gb-sfp

        exit

        mda 2

            mda-type m10-1gb-sfp

        exit

    exit

    card 3

        card-type iom-20g

        mda 1

            mda-type m12-ds3

        exit

        mda 2

            mda-type m12-ds3

        exit

    exit

    card 8

        card-type iom-20g

        mda 1

            mda-type m8-oc12/3-sfp

        exit

        mda 2

            mda-type m16-oc12/3-sfp

        exit

    exit

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments