manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Operator'S Manual

Share
Download
Alamo BUSH HOG RMB 1660 Operator'S Manual Download Page 185

MAINTENANCE

RMB 1660   01/22

Maintenance Section 5-11

© 2022 Alamo Group Inc.

MAINTENANCE

Hydraulic Component Maintenance Schedule

PROPER TORQUE FOR FASTENERS

The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to
this chart to determine the grade of bolts and the proper torque except when specific torque values are
assigned in manual text.

RECOMMENDED TORQUE IN FOOT POUNDS  UNLESS OTHERWISE STATED IN THE MANUAL*

NOTE:

 These values apply to fasteners as received from supplier, dry or when lubricated with normal engine

oil. They do not apply if special graphitic or molydisulphide greases or other extreme pressure lubricants are
used. This applies to both UNF fine and UNC coarse threads.

Component

Installation

200

400

600

800

1000

1200

1400

1600

1800

2000

2200

Pump Drive Shaft Check and Lubricate

X

X

X

X

X

X

X

X

X

X

X

X

Pump Mounting Bolt torque check (Inspect Daily)

X

X

X

X

X

X

X

X

X

X

X

X

Charge Pump Filter

Installation

X

X

X

Pressure Filter to the Control Valve

Installation

X

X

X

Return Canister Filter Element

Installation

X

X

X

Hydraulic Oil Change

Installation

X

X

Hydraulic Oil Particle Count Testing

X

X

X

X

Hydraulic Tank Breather Filter

Installation

Inspect

Replace

Hydraulic Tank Suction Screen

Installation

Inspect

Inspect

Hydraulic Hose Inspection/Replacement

Installation

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Inspect

Cooling Fan Clean and Inspect

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Check Hydraulic Fluid Level (Inspect Daily)

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Mower Blades  Replace (INSPECT DAILY)

X

X

X

X

X

X

X

X

X

X

X

Blade Bolts Replace (INSPECT DAILY)

X

X

X

X

X

X

X

X

X

X

X

Blade Bar Assembly Replace

Installation

X

X

Spindle Lube Replacement (INSPECT DAILY)

X

X

X

Spindle Bearing Pre-load Inspection

X

X

X

X

X

X

X

X

X

X

X

X

Mower Debris Guard Inspect/Replace

X

X

X

X

X

X

X

X

X

X

X

X

Pivot Point Lubrication

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

Daily

King Pin Bearing Replacement

Installation

X

Pivot Pin Bearing replacement (Steel)

Installation

X

Pivot Pin Bearing Replacement (Fiber)

Installation

X

X

Inspect Operation And Safety Decals Replace 
when faded, torn or missing.

X

X

X

X

X

X

X

X

X

X

X

X

Repeat the Maintenance Schedule based on the hours indicated for the life of the machine

Hours of Operation

Summary of Contents for BUSH HOG RMB 1660







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands