background image

OPERATION

PVB-PVS   08/20

Operation Section 4-10

O

PE

R

AT

IO

N

© 2020 Alamo Group Inc.

7.2 Soil Pulverizer Pre-Operation Inspection/Service

Before each use, a complete inspection and service is required to ensure the Pulverizer is in good and safe

working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure

the implement is ready for operation, conduct the following:

7.1 Tractor Pre-Operation Inspection/Service

Refer to the tractor operator’s manual to ensure a

complete  pre-operation  inspection  and  scheduled

service  is  performed  according  to  the

manufacturers  recommendations.  The  following

are some of the items that require daily service and

inspection:

Tire condition/air pressure

Wheel lug bolts 

Steering linkage

PTO shield 

SMV sign is clean and visible

Tractor’s lights are clean and functional

Tractor Seat belt is in good condition 

Tractor ROPS is in good condition

ROPS is in the raised position

No tractor oil leaks 

Radiator free of debris 

Engine oil level and condition

Engine coolant level and condition 

Power brake fluid level 

Power steering fluid level 

Fuel condition and level 

Sufficient lubrication at all lube points

Air filter condition  

OPS-U-0030

Periodically  inspect  all  moving  parts  for  wear  and  replace  when

necessary with authorized service parts.  Look for loose fasteners, worn

or  broken  parts,  and  leaky  or  loose  fittings.    Make  sure  all  pins  have

cotter pins and washers.  Serious injury may occur from not maintaining

this machine in good working order.  

(SG-21)

Summary of Contents for BUSH HOG PVB























































Reviews: