GB
46
CS 4235
Operation
IMPORTANT!
Danger of damaging the chain saw
The chain saw will be severely damaged
if there is too little or even no saw chain
oil in the tank or if it has dried/is sticky.
Dried/sticky saw chain oil can lead to
damage to oil-channelling components
and the oil pump.
Damage also occurs if used oil is used.
The use of used oil leads to environmen-
tal damage!
■
Each time before starting work,
check that enough saw chain oil is
present in the tank.
■
If the oil level is low, refill saw chain
oil.
■
Do not use any used oil!
6.2
Putting on the rechargeable battery belt
system (10) to (13)
Put on the rechargeable battery belt system as
shown in Figures (10) to (13).
6.3
Inserting/removing the battery (14)
Inserting the battery
1. Push in (14/a) the rechargeable battery
(14/1) into the rechargeable battery belt sys-
tem (14/2) until it locks.
Pull out the rechargeable battery
1. Press and hold the unlock button (14/3) on
the rechargeable battery (14/1).
2. Pull out (14/b) the rechargeable battery
(14/1).
6.4
Connecting the voltage supply (15, 16)
Mounting the connecting cable
1. Align the first connector of the connecting ca-
bles (15/1) to the guiding pin and guide slot
of the rechargeable battery belt system con-
nector (15/2), join, and turn slightly clockwise
until the locking and unlocking switch (15/3)
audibly engages.
2. Align the second connector of connecting ca-
ble (16/1) with the guiding pin and guide slot
of connection socket (16/2) of the tool, push
(16/a) into connection socket (16/2), and turn
slightly clockwise until the locking and un-
locking switch (16/3) audibly engages.
Dismounting the connecting cable
1. Pull locking and unlocking switch (15/3) back-
wards (15/b), turn the connector slightly to
the left and pull out (15/c).
2. Pull locking and unlocking switch (16/3) back-
wards, turn the connector slightly to the left
and pull out (16/b) of the connection socket
of the tool (16/2).
6.5
Switching the motor ON and OFF (17)
CAUTION!
Danger of hearing impairment!
The operation of the chain saw causes
intense noise that can cause hearing im-
pairment.
■
During work with the chain saw,
wear ear defenders.
NOTE
Release the chain brake each time be-
fore switching on the chain saw.
Switching on the motor:
1. Release the chain brake.
2. Press and hold locking button (17/1) with
your thumb.
3. Press and hold throttle lever (17/2).
4. Release locking button (17/1). It is not neces-
sary to keep the locking button pressed once
the chain saw has started. The locking button
is intended to prevent inadvertent starting of
the chain saw.
Switching off the motor:
1. Release throttle lever (17/2).
Summary of Contents for Solo CS 4235
