manualshive.com logo in svg

Akytec SMI200, User Manual, Page: 14 / 15

Share
Download
Akytec SMI200 User Manual Download Page 14

 

Transportation and storage 

 

akYtec GmbH · Vahrenwalder Str. 269 A · 30179 Hannover · Germany · Tel.: +49 (0) 511 16 59 672-0 · www.akytec.de  

 

13

 

9  Transportation and storage 

Pack the device in such a way as to protect it reliably against impact for storage and transportation. 
The original packaging provides optimum protection. 

If the device is not taken immediately after delivery into operation, it must be carefully stored at a 
protected location. The device should not be stored in an atmosphere with chemically active sub-
stances. 

Permitted storage temperature: -20...+55 °C 

►

 NOTICE 

Transport damage, completeness 
The device may have been damaged during transportation. 
Check the device for transport damage and completeness! 
Report the transport damage immediately to the shipper and akYtec GmbH! 

 

►

 

NOTICE 

Before powering on, make sure that the device was stored at the specified ambi-
ent temperature (-20 ... +55 °C) for at least 30 minutes. 

 

Summary of Contents for SMI200
















Reviews:

No comments