Akku Vision e-bike vision 10046 Manual/Safety Notes Download Page 6

 

 

Date 2022-04-19 

Akku Vision - Manual EBV E-Bike Battery InFrame compatible to Bosch* Active / Performance 

S. 

6

 / 

9

 

Index 02 

*Bosch is a trademark of the Robert Bosch GmbH 

 

 

Safety notes for charging 

Please pay particular attention to the following points when charging:

 

 

 

Connect the charger only to a suitable mains supply.

 

 

Do not charge NiCd, NiMh or primary cells!

 

 

Use the charger only with the appropriate EBV E-Bike Batteries of Akku Vision!

 

 

When not using for a longer period, disconnect the mains supply and also connected batteries.

 

 

The charging time varies depending on the battery’s capacity and charger type.

 

 

Do not charge the battery below 0° and not above 45° C. The battery management system will not allow to 
start the charging process.

 

 

Please charge your EBV E-Bike Battery only under supervision and on a non-combustible surface (both 
battery and charger).

 

 

The charger is designed for operation in ventilated, dry and dust-free environment. Never expose to rain or 
extreme heat. Allow adequate air circulation.

 

 

Do not cover the charger, nor the battery.

 

 

Ensure that that the plugs and sockets of the charger are not damp or contaminated.

 

 

Do not touch plugs and sockets of the charger with wet hands.

 

 

Do not try to convert or disassemble the charger.

 

 

Before the charger is connected to the mains, please ensure that line voltage matches to the supply voltage 
of the charger. The charger’s needed voltage is indicated on its nameplate on the backside.

 

 

A charger with a damaged power supply cord or plug must not be connected to the electrical grid and must 
promptly replaced or repaired by the E-Bike service center.

 

 

Penetration of water and moisture into the charger must be avoided in any case. Should this have happened, 
power off the charger (by turning off the fuse) immediately. Disconnect the charger from the mains and let 
it be checked by the Akku Vision service center.

 

 

A sudden temperature change from cold to hot, there could be condensation water on and in the charger. 
In this case, wait for connecting to the mains until the charger is as warm as the room. Try to avoid this case 
by storing the charger where you use it.

 

 

For maximum life of your battery, charge it only within 10° and 30° C temperature range. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for e-bike vision 10046










Reviews: