AJA KONA 4 Installation And Operation Manual Download

Page: 45 / 89

KONA Capture, Display, Convert v15.2 45 www.aja.com

Video Setup Screen

Figure 30. Video Setup Screen, KONA 5

The Video Setup screen shows various other settings which will affect how

video inputs and outputs behave, and how KONA interacts with some software

applications.

Video Setup

Progressive Pref

Allows you to choose to prefer p (progressive frames) or PsF (progressive

segmented frames) on non-interlaced output. This feature is used to default the

hardware to use either p or PsF output over SDI when it has not been specified by

the application.

Color Space

Sets the video color space. Select from:

•  Auto
•  Rec 601
•  Rec 709

Gamma

Sets the video gamma. Intended for use with legacy Apple displays. Select from:

• Auto
• Gamma 1.8

Summary of Contents for KONA 4


























































































Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands

AJA KONA 4, Installation And Operation Manual

Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands