AJA KONA 4 Installation And Operation Manual Download

Page: 24 / 89

KONA Capture, Display, Convert v15.2 24 www.aja.com

Figure 19. Update Completed Messages

6. Click

Shut Down

to power down the computer.

7. Restart the computer.
8. Open AJA Control Panel. The AJA hardware with the updated firmware

should be recognized by the Control Panel application.

Firmware Versions

KONA 5 supports two different versions of firmware that have different

capabilities. One version of firmware can be installed at a time.

• 4K Mode—Supports 4K (4096x2160), UltraHD (3840x2160), 2K, HD, SD at

12-bit, 10-bit, and 8 bit with the appropriate 12G-SDI (SMPTE-2082), 6G-SDI

(SMPTE-2081), 3G-SDI & 1.5G-SDI links. One channel of 12G-SDI is available for

input on SDI 1 and output on SDI 3.

• 8K Mode—supports 8K (8192x4320) and UltraHD2 (7680x4320) over four

12G-SDI links at 10-bit and 8-bit. Also supports 4K, UltraHD, 2K, HD, and SD

over single 12G link.

KONA 4 supports two different versions of firmware that have different

capabilities. One version of firmware can be installed at a time.

• UFC Mode—Supports SD, HD, and 2K formats (allows up/down/cross-

conversion)

• 4K Mode—Supports SD, HD, 2K and UltraHD (3840x2160) and 4K (4096x2160)

formats (disables up/down/cross-conversion)

NOTE: KONA 1 currently supports a single firmware version.

Summary of Contents for KONA 4


























































































Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands

AJA KONA 4, Installation And Operation Manual

Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands