Ki Pro Ultra v1.2r1
www.aja.com
53
9.2 INTERVAL TIME
Determines the time period from which the interval frames are selected. These are the
options:
32.0 Loss of Video
This parameter selects whether recording continues when valid video is not present.
These are the options:
NOTE:
If CONT Rec is selected, and a loss of video is encountered, a graphic with the text “LOSS OF
VIDEO” superimposed over color bars will appear. Be sure to check your source and video
connections if you are experiencing a loss of video.
35.2 Remote Control
This parameter is for setup of remote RS-422 machine control.
Control from RS-422:
To control the Ki Pro via the RS-422 port, this Configuration option must be set to
RS422 Only
. If this option is not set, the device will look to the controller as if the tape is
ejected. Once a clip is selected, frame accurate playback control of the current clip is
immediately possible. The timecode format delivered via RS-422 will be dependent upon
the current clip. Note that the device will allow you to shuttle to anywhere in the full 24-
hour timecode, but the current clip will exist at the clip's own timecode. Playlists are
supported as long as the clips are of the same format and frame rate.
Capture Control from RS-422:
To perform an edit-to-tape function, the selected clip must be in the format, rate, and
timecode you want to capture. If you don't yet have a clip in your input format, you can
create one by manually capturing a short clip of the input you'll be editing. Once this clip
is selected, you can then shuttle to any point in the 24-hour timecode. Your edit can take
place anywhere in the 24-hour timecode. The device does not differentiate between
insert or assemble, nor does it support video, audio or timecode only edits. Each edit
operation will produce a new clip at the edit in point with a duration equal to the edit.
The clip will contain all video and audio fed to the device. You will not be able to insert
into an existing clip. Be aware that you should set your pre-roll to five (5) seconds or
greater to allow the device sufficient time to lock to the video input.
41.1 VIDEO SG FRMT
This parameter determines the video format output from Ki Pro Ultra’s internal test signal
generator. This parameter is used with parameter 41.2 to determine the type of video
test signal output by Ki Pro Ultra.
NOTE:
While the Ki Pro Ultra may be configured for a YCbCr or RGB signal generator, the output is
ultimately determined by the selection made in the 1.6 SDI OUT menu parameter.
Example:
The 41.1 VIDEO SG FRMT is set to 1080p 23.98 RGB and the 1.6 SDI OUT is set to SDI 1
RGB, then the output will be RGB. If the 41.1 VIDEO SG FRMT is set to 1080p 23.98 RGB
and the 1.6 SDI OUT is set to SDI 1 YCbCr, then the output will be YCbCr even though the
signal generator was configured for RGB.
Second
Minute
Hour
The second from which interval frames are selected.
The minute from which interval frames are selected.
The hour from which the interval frames are selected.
Stop Rec (default)
Cont Rec
Recording stops when video is lost
Recording continues when video is lost
Local Only (default)
RS-422 Only
Enables local control only. RS-422 is disabled.
Enables RS-422 control
Summary of Contents for Ki PRO ULTRA
