manualshive.com logo in svg

AJA Ki PRO mini, Installation & Operation Manual

Share
Download
AJA Ki PRO mini Installation & Operation Manual Download Page 37

KiPro Mini v4.2

www.aja.com

37

 

            

For the MENU mode, depressing one of the 3 MENU buttons (STATUS, CONFIG, or MEDIA) 
will enter the corresponding menu.

In the STATUS menus, the Select buttons will cycle through the various 
STATUS screens. The Adjust buttons have no effect on the STATUS 
menu. 

The first STATUS page shows the format and frame rate of the material being recorded or 
played back. The second page shows the timecode settings. The third page may shows 
the Interval Record status (if Interval Record is enabled).

The displays for the STATUS menu are shown below:                   

In the CONFIG and MEDIA menus, the Select buttons select various adjustable 
parameters, and the Adjust buttons adjust the selected parameter. When entering a 
menu, the system remembers and returns to the last selected parameter. 

SC26ATK12

REEL 001              S1

01:04:23:10           47%

STATUS Menu (Record Mode)

RECSlot Selected

Recording FormatFramerate

ProResProRes Type

STATUS Menu (Play Mode)

PLAYSelected Slot

Clip FormatClip Framerate

ProResClip ProRes Type

STATUS Menu (Timecode)

TC In

TC Value

01:00:00:00

Interval Rec On

Interval: 1

Time: Sec

USO 

RESTRITO

Summary of Contents for Ki PRO mini











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands