AJA FS-HDR Installation And Operation Manual Download Page 101

Page: 101 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 101 www.aja.com

See

"Networking" on page 29

for detailed setup instructions for connecting the

FS-HDR to a network. Consult your network administrator about how to configure

network settings.

IP Address Type

IP Address Type determines the type of TCP/IP network configuration used by the

FS-HDR. DHCP enables the FS-HDR to connect to the network DHCP server, which

assigns the IP Address, Netmask, and Gateway automatically. Static lets you set

these parameters manually.

NOTE: If the IP Address Type is DHCP, the IP Address, Netmask, and Default Gateway

are gray, indicating they are set automatically and cannot be changed unless

IP Address Type is first set to Static. Changes are saved and activated upon

confirmation using the Apply button.

DHCP (default)

Static Addr

Select automatic IP address assignment from the LAN DHCP server.

If the FS-HDR cannot find a DHCP server, it fails over to the static IP

address.

Assign a static IP address manually. The factory default static IP

address: 192.168.0.2

IP Address

IP Address determines the static IP address used by the FS-HDR for TCP/IP

networking. (Networking is discussed in Chapter 3, Network Connection.) Consult

your network administrator about how to set this value.

Variable

IP Address Type

is set to

DHCP

, the IP address is set automatically by

the network DHCP server and cannot be entered here.

IP Address Type

is set to

Static

, enter an IP address compatible with

your LAN here. Also enter a netmask and default gateway address

in the following two parameters. Click

Apply

when you are ready to

apply all three entries to change the FS-HDR’s network addressing.

IP Address Type

is set to

DHCP

and there is a DHCP failure, the IP

address is set to the static IP address. The default static IP address is

192.168.0.2

Netmask

Netmask determines the subnet mask used by the FS-HDR for TCP/IP networking.

Variable

Enter a subnet mask compatible with your LAN. This is only needed

for Static IP configurations. The factory default

Subnet Mask

255.255.255.0

IP Address Type

is set to DHCP, the Subnet Mask is set by the DHCP

server and cannot be changed by the user.

Default Gateway

Default Gateway determines the gateway or router used on your LAN for TCP/IP

networking.

Summary of Contents for FS-HDR


































































































































Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands

AJA FS-HDR, Installation And Operation Manual

Search results

Summary of Contents for FS-HDR

Reviews:

Related manuals for FS-HDR

Brands by name

Popular brands