manualshive.com logo in svg

AJA BRIDGE LIVE, Installation And Operation Manual

Share
Download
AJA BRIDGE LIVE Installation And Operation Manual Download Page 98

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 98 www.aja.com

 

Figure 148.  Configuring network connectivity

Use For

Select one of the following from the pull-down menu: 

•  Don't Use
•  Administration
•  Input/Output
•  Input/Output and Administration

NOTE:  Typically Administration is applied to only one port. If applied to more than one 

port, you will see a warning message (but not an error). 

NOTE:  With a dual NIC setup, you cannot have both NICs connected to the same 

network.

Assign Address

Select one of the following: 

•  DHCP
•  Static

•  IPv4 Address
•  Mask
•  Default gateway

•  Mask
•  Gateway

Click 

Next step

. 

Configuration of GPU and CPU Acceleration

This section is informational only. It reports detected GPUs and CPUs for 

acceleration of video frame decoding and encoding. 

Summary of Contents for BRIDGE LIVE












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands