manualshive.com logo in svg

AJA BRIDGE LIVE, Installation And Operation Manual

Share
Download
AJA BRIDGE LIVE Installation And Operation Manual Download Page 68

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 68 www.aja.com

 

Selecting the Input Stream Source (SDI Channel)

Figure 108.  Input stream source selection

For the Input stream configuration options, make selections for Type, SDI device, 

and Port. In this example, the HD program feed for the Production Studio is 

connected to Port #3 of the BRIDGE LIVE device. So the following selections were 

made: 

•  Type: SDI
•  SDI device: AJA Corvid 44 12G BNC - 0
•  Port: Port #3

Auto-Detecting Video Streams

In the lower-right area, click Apply configuration. 

Figure 109.  Apply configuration button

The Input stream configuration options column updates to show a new heading 

called "Auto-detected video streams." 

Figure 110.  New heading displays called "Auto-detected video streams"

Beneath the heading, what is shown is "Video #1: Uncompressed 1920x1080p 

@59.94Hz 4:2:2 10-bit. 
Click the signal that is listed. The Input stream video configuration options 

section expands and is auto-populated with the auto-detected video stream 

properties. 

Summary of Contents for BRIDGE LIVE












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands