AJA BRIDGE LIVE Installation And Operation Manual Download Page 57

Page: 57 / 139

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 57 www.aja.com

Selecting the Input Stream Source

Figure 77. Input stream source selection

For the Input stream configuration options, make selections for Type, IP address,

Port, Ethernet card. In this example, the following selections were made:

• Type: SRT
• IP address: enter the IP address for the Ethernet card of the BRIDGE LIVE

device that is sending the signal. In this example, it is the IP address of the

BRIDGE LIVE device located in the Production Studio.

•  Port: 5050
•  Ethernet card: Ethernet card 2
•  SRT mode: Caller
•  Compliance with: Auto-detected

Auto-Detecting Video Streams

In the lower-right area, click Apply configuration.

Figure 78. Apply configuration button

The Input stream configuration options column updates to show a new heading

called "Auto-detected video streams."

Figure 79. New heading displays called "Auto-detected video streams"

Beneath the heading, what is shown is "Video #1: H.264 1920x1080p @59.94Hz

4:2:0 8-bit."

NOTE: Auto-detect can detect the signal only if it is actually present to the device.

Click the signal that is listed. The Input stream video configuration options

section expands and is auto-populated with the auto-detected video stream

properties.

Summary of Contents for BRIDGE LIVE












































































































































Search results

Summary of Contents for BRIDGE LIVE

Reviews:

Brands by name

Popular brands

AJA BRIDGE LIVE, Installation And Operation Manual

Search results

Summary of Contents for BRIDGE LIVE

Reviews:

Brands by name

Popular brands