manualshive.com logo in svg

AJA BRIDGE LIVE, Installation And Operation Manual

Share
Download
AJA BRIDGE LIVE Installation And Operation Manual Download Page 11

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 11 www.aja.com

 

Encoding and Decoding Protocols Supported

The following values are recommendations only. You can use lower values if you 

need to. If you have good enough network throughput, you can use higher bit 

rates. 

Encoding

BRIDGE LIVE supports encoding from SDI to Stream, and from SDI to JPEG 2K 

Stream (with optional license). See Table 1 and Table 2 below for encoding signal 

specifications. 

Table 1.  SDI to Stream Encoding

Encode

HD (1080p)

UltraHD

Supported Protocols

H.264 (AVC)  

4:2:0, 8-bit

4 simultaneous 

up to 60p
8 to 15 Mbps

1 up to 60p
40 to 75 Mbps

SRT, RTMP/S, MPEG-TS

H.264 (AVC)  

4:2:2, 10-bit (HQ)

4 simultaneous 

up to 30p
50 to 75 Mbps

1 up to 30p
80 to 120 Mbps

SRT, RTMP/S, MPEG-TS

H.264 (AVC)  

4:2:2, 10-bit (HQ)

2 simultaneous 

up to 60p

1 up to 30p

SRT, RTMP/S, MPEG-TS

H.265 (HEVC) 

4:2:0, 8/10-bit

4 simultaneous 

up to 60p
5 to 12 Mbps

1 up to 60p
35 to 110 Mbps

SRT, RTMP/S, MPEG-TS

MPEG2 4:2:0,  

8-bit

4 simultaneous 

up to 30p/60i
8 to 15 Mbps

N/A

SRT, RTMP/S, MPEG-TS

MPEG2 4:2:2,  

8-bit (HQ)

4 simultaneous 

up to 30p/60i
10 to 20 Mbps

N/A

SRT, RTMP/S, MPEG-TS

NDI

150 Mbps

250 Mbps

SRT, MPEG-TS, RTP/

UDP, UDP

Table 2.  SDI to JPEG 2K Stream Encoding (Optional License)

Encode

HD (1080p)

UltraHD

Supported 

Protocols

JPEG2K TR-01 

2013 4:2:2,  

10-bit

4 simultaneous 

up to 60p
80-220 Mbps

1 up to 60p
up to 800 Mbps

SRT, MPEG-TS
Note: No RTMP/S

Decoding

BRIDGE LIVE supports decoding from Stream to SDI, and from JPEG 2K Stream 

to SDI (with optional license). See Table 3 and Table 4 below for decoding signal 

specifications. 

Summary of Contents for BRIDGE LIVE












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands