manualshive.com logo in svg

AISWEI ASW1000S-S, Installation And Operating Instructions Manual

Share
Download
AISWEI ASW1000S-S Installation And Operating Instructions Manual Download Page 63

 

Installation and Operating Instructions V00

                                                                     

63

 

10.7 Tools and torque

 

Tools and torque required for installation and electrical connections. 

 

 

Tools, model 

Object 

Torque 

Torque screwdriver, T25 

Screws for the cover 

2.5Nm 

Torque screwdriver, T20 

Screw  for  second  protective 
grounding connection 

1.6Nm 

Screws for connecting the inverter 
and wall bracket 

Flat-head screwdriver, 

blade with 3.5mm 

Sunclix DC connector 

/ 

Flat-head screwdriver, 

blade 0.4×2.5 

Smart meter connector 

/ 

/ 

Stick 

Hand-tight 

Socket 

wrench 

Open end of 33    Swivel nut of M25 cable gland 

Hand-tight 

Open end of 15    Swivel nut of sunclix connector 

2.0Nm 

Wire stripper 

Peel cable jackets 

/ 

Crimping tools 

Crimp power cables 

/

 

Hammer drill, 

drill bit of Ø10 

Drill holes on the wall 

/ 

Rubber mallet 

Hammer wall plugs into holes 

/ 

Cable cutter 

Cut power cables 

/ 

Multimeter 

Check electrical connection 

/ 

Marker 

Mark the positions of drill holes 

/ 

ESD glove 

Wear ESD glove when opening the 
inverter 

/ 

Safety goggle 

Wear  safety  goggle  during  drilling 
holes. 

/ 

Anti-dust respirator 

Wear  anti-dust  respirator  during 
drilling holes. 

/ 

Summary of Contents for ASW1000S-S






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands