manualshive.com logo in svg

AISWEI ASW1000S-S, Installation And Operating Instructions Manual

Share
Download
AISWEI ASW1000S-S Installation And Operating Instructions Manual Download Page 53

 

Installation and Operating Instructions V00

                                                                     

53

 

10.3 General data 

General data 

ASW1000S-S/ 1500S-S / 2000S-S / 3000S-S 

communication:   
WIFI/Meter/RS485/GPRS 

●

 /

●

 / 

○

 / 

○

 

Display 

LED 

Earth Fault Alarm 

cloud based, audible and visible(AU) 

Zero power output 

Via connecting Smart meter 

Dimensions   
(W x H x D mm) 

320x264x94 

Weight 

6.5Kg 

Cooling concept 

convection 

Noise emission (typical) 

< 15 dB(A)@1m 

Installation 

indoor & outdoor 

Mounting information 

wall mounting bracket 

DC connection technology 

SUNCLIX 

AC connection technology 

Plug-in Connector 

Operating temperature range 

-25

℃

…+60

℃

 / -13

℉

…+140

℉

 

Relative humidity (non-
condensing) 

0% ... 100% 

Max. operating altitude 

4000m(>3000m derating) 

Degree of protection 
(according to IEC 60529) 

IP65 

Climatic category (according 
to IEC 60721-3-4) 

4K4H 

Topology 

BOOST+H6.5 

Self-consumption (night) 

<1W 

Radio technology 

WLAN 802.11 b / g / n 

Radio spectrum 

2.4 GHz 

Standby power   

<5W 

 

 

Summary of Contents for ASW1000S-S






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands