Airtecnics K7 600 A OH+FC Installation, Operation And Maintenance Manual Download Page 18 | Manualshive

Page: 18 / 22

background image

18

PCB replacement

K7 600 A OH+FC (standard control) -> Open the inspection door and disconnect the cables from the board
that are visible and the capacitor. Unscrew the board located on one of the sides, disconnect the power supply
and pull it:

K7 600 A OH+FC CL (advanced Clever control) -> Open the inspection door and disconnect the cables from
the board that are visible and the capacitor. Unscrew the power board from the top and perform the necessary
repair:

K7 600 A OH+FC SS (standard control IP55) -> Open the waterproof box above the purifier and disconnect all
cables from the board. Unscrew the bracket clamp to the waterproof box and finally unscrew the bracket plate.

«
...
16
17
18
19
20
...
»

Summary of Contents for K7 600 A OH+FC























Reviews:

No comments

Related manuals for K7 600 A OH+FC

Brand: Vax Pages: 12

Brand: Vax Pages: 9

AG TN1DKH Series

Brand: Samsung Pages: 22

Brand: Fakir Pages: 28

Brand: Unitekno Pages: 52

Brand: Amana Pages: 82

Brand: aldes Pages: 4

ALPHA iQ iAquaLink CONTROL

Brand: Zodiac Pages: 25

Ultramax EZ Series

Brand: Ultravation Pages: 2

Brand: Kärcher Pages: 284

TherapyAir iOn PWC-570

Brand: Zepter Pages: 17

Brand: Dirt Devil Pages: 32

Brand: Bryant Pages: 28

Brand: Levoit Pages: 20

VC-17703050-BSTR

Brand: Singer Pages: 36

Brand: Hatari Pages: 9

Brand: CIAT Pages: 18

Brand: Sencor Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands