5-16
3� If another button is pressed before the 5 second
time is up for the BATT button, the display will
immediately switch to show the value for the new
button� The 5 second time-out is restarted every
time a button is pressed�
4� There is no hold mode for the battery voltage
Refrigerator
Review all refrigerator literature supplied in your
owner’s packet or stored in the refrigerator prior to
operating�
Flying Cloud models have all-electric refrigerators
which feature a strong 12V compressor, no LPG
is required� Depending on your model, to turn the
refrigerator on, touch and release the ON/OFF
button� The blue indicator light will glow solid blue to
indicate that the refrigerator is on, or use the wide
range thermostat designed to sense the evaporator
(cold plate) temperature� The coldest position on
the thermostat is reached by turning the knob to the
right (clockwise); conversely turning the thermostat
knob to the left (counterclockwise) yields a warmer
setting� The OFF position is reached by turning hard
counterclockwise past the click� The reference point is
shown with an indicator sticker beside the knob�
To get ready for a trip, start your refrigerator and let it
cool for eight hours before loading with food� For the
best cooling performance, let air move freely inside the
compartments�
It will be necessary to defrost the refrigerator and
freezer compartment from time to time� Frequency
depends on usage, the number of times the door is
opened and closed, and the humidity level� To defrost,
turn the refrigerator off and prop open the door� Most
of the condensation will run out of the condensate tube
to the outside of the trailer� Use dry towels to keep
extra condensation from dripping onto the floor. Do not
use heat or sharp objects to speed up the defrosting
process as this can damage the unit�
Clean the interior periodically with mild cleaner or
solution of liquid dish detergent and warm water� Rinse
with a solution of baking soda and clean water�
CAUTION
Speeding up the defrost process with a knife
or scraper is strongly discouraged due to the
likelihood of rupturing the refrigerant circuit.
automatically� If another button is pressed before the
display shuts down, then the new level will immediately
be shown� If the same button is pressed twice, the
display will hold on that tank and continue to show
updated levels for 5 minutes before shutting off� This
allows the user to monitor the filling or draining of the
tank� By pressing two buttons at once, the diagnostic
functions can be accessed�
Sender pads are installed and stuck to the sides of
the holding tank� The sender pad scans the water
level through the tank wall using digital techniques
programmed into the sender microprocessor�
To Read a Water or Sewer Tank Level
1� Press the button corresponding to the tank to be
checked and release it, the display will show the
levels in percent on the LED display� If no other
button is pressed, then the display shuts off after
about 5 seconds�
2� If another button (including BATT) is pressed
before the 5 second time is up for the first button,
the display will immediately switch to show the new
level or voltage� The 5 second time-out is restarted
every time a button is pressed�
3� To continuously display a reading, press and
release the desired button, and then press the
same button a second time� When the button is
released, the display will be on hold mode, which
is indicated by the decimal point on the right hand
side turning on� While the display is in the hold
mode it will recheck the level once per second
so the user can watch the level change while the
tank is being filled or drained. The display will
automatically shut off after 5 minutes in hold mode�
To end the hold mode before the 5 minutes is up,
press any tank button, and the display will shut off�
To Read the Battery Voltage
1� Press the BATT button and release it, the display
will show the battery voltage on the LED display
2� If no other button is pressed, then the display will
shut down after about 5 seconds� If the BATT
button is held down, the display will continuously
recheck the voltage and show the updated value�
The reading may flicker back and forth between
two values�
Summary of Contents for FLYING CLOUD 2023
Page 1: ...2 0 2 3 F LY I N G C L O U D SCAN ME O w n e r s M a n u a l...
Page 4: ...2023 Flying Cloud NOTES NOTES...
Page 6: ...2023 Flying Cloud 1 2 Introduction NOTES NOTES...
Page 30: ...2023 Flying Cloud 4 6 Floor Plans And Specifications NOTES NOTES...
