manualshive.com logo in svg

Airspan AirSynergy3, Installation Manual

Share
Download
Airspan AirSynergy3 Installation Manual Download Page 49

                                 

AirSynergy3 Equipment Installation Guide

 

Page 49 |                                     Commercial in Confidence                                           SYN-UG-018 

 

Appendix B 

– Field assembly of Back to back AirSynergy units 

In cases where 2 AirSynergy radios are to be installed on the same mounting bracket some additional 
installation steps are required as follows: 

 

Removal of the existing stud mounting plates (4 positions)  from  each  AirSynergy unit.  Each plate is 
secured with 2 countersunk head screws.  

 

Figure 64 - Removing the existing stud mounting plates 

 

 

Note: The screws should be replaced with a new set of 16 pieces with fresh 
locking patches on the threads when re-assembling with the joining plates. A new 
set of screws is supplied with the back to back joining kit.

 

 

Re-assembly with the joining plates. The studs with flange nuts must all be at the same end. A typical 
arrangement will be with the AirSynergy with connectorised RF ports to be mounted at the back. The 
mounting studs will then all be on the sides of the connectorised unit as shown in the figure.  Fit all 4 
plates to one of the AirSynergy units then slide the 2

nd

 Synergy unit into place between the brackets.  

 

 

Figure 65 - Fitting the stud joining plates 

 

Summary of Contents for AirSynergy3


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands