manualshive.com logo in svg

Airspan AirSynergy3, Installation Manual

Share
Download
Airspan AirSynergy3 Installation Manual Download Page 24

                                 

AirSynergy3 Equipment Installation Guide

 

Page 24 |                                     Commercial in Confidence                                           SYN-UG-018 

 

3.2  Fit Front Sector Antenna to AirSynergy 

The AirSynergy unit can be used either with a sector antenna mounted directly on the front or with a 
remotely attached RF antenna. This document describes the installation procedure for the front mount 
antenna (2.x and 3.xGHz bands. For the installation of separate antennas follow the antenna 
manufacturer’s instructions and connect to the AirSynergy using suitable feeder cable tails. (N-Type 
RF connections should all be weather-proofed).  For details for other frequency front mountable 
antenna variants and front antenna mounting arrangements for double radio units please contact 
Airspan Product Line Management ) 

In all cases where a front mount antenna is not fitted a sun shield should be fitted

.

 

To mount the front antenna, perform the following steps: 

3.2.1   Fit the antenna to the mounting plate. The 4 studs on the back of the antenna pass through the 
holes on the front face of the mounting plate and secure into position with the 4 sets of M4 nuts and 
washers (plain + spring) provided in the kit. Carefully position the flying lead RF cables as shown in 
Figure 20 and secure in place to the eyelets in the back of the mounting plate with cable ties 
(provided). The cables are formed  with a cross-over at the bottom 

 

 

Note: 

 

It is recommended to place some cardboard or paper under the unit to 

protect it from scratching.

 

 

 

Figure 23 – Fixing the front mount antenna to the mounting plate 

3.2.2   Fit the assembled antenna and mounting plate to the AirSynergy unit using the M5 SEMs (2 
each side) and connect the RF cables to the N type RF ports at the top of the AirSynergy. 

Note: the plate is mounted with the side slots to the top so that the required down-tilt can be set. 

 

Figure 24 –Fitting the Front mount antenna assembly to AirSynergy  

Summary of Contents for AirSynergy3


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands