manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Installation Manual

Share
Download
Airspan AirSpeed 1030 B48 Installation Manual Download Page 27

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

25 

 

 

4  AirSpeed 1030 B48 Installation 

AirSpeed 1030 B48 offers two optional methods for outdoor mounting using the mounting kit, either: 

  Pole Mounting 

  Wall mounting   

The AirSpeed 1030 B48 Mounting Kit - includes a back bracket and pole/wall mounting bracket for 
fastening the unit to a pole or on a wall. Prior to installation the back bracket must be assembled on 
the AirSpeed unit and then the mounting bracket must be affixed in place on either the pole or a wall. 

Note:

 Mounting kits are ordered separately. 

4.1 Back Bracket Assembly 

Prior to installation the back bracket must be assembled on the AirSpeed unit, (unless pre-assembled). 

1. 

Lie the unit on its face to expose the back. 

2. 

Orient the back bracket so the lifting handle will be assembled in the direction of the top 
panel, where the GPS and RF ports are located.  

3. 

Line up the four (4) holes on the back bracket with four (4) threaded holes on the back of the 
AirSpeed unit. 

4. 

Insert and screw in the four (4) (M6 X 20) screws to tighten (tighten to a torque of no more 
than 5.2 Nm (46.02 in-lbs.) max., as shown below. 

 

Figure 6: Back Bracket Assembly 

 

 

Summary of Contents for AirSpeed 1030 B48


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands