manualshive.com logo in svg

Airspan AirHarmony 4000 DC, Installation Manual

Share
Download
Airspan AirHarmony 4000 DC Installation Manual Download Page 32

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

26 

Caution:

 Proper local rigging and hoisting practices should be followed when installing 

the AirHarmony-4000. 

 

4.2.1

 

Mounting on a Wooden Pole 

The following images show the pole mount assembly on a wooden pole. 

Caution:

 Take care to install the Pole/Wall mounting plate in the correct orientation. 

Verify that the mounting pins are facing upwards as shown below. 

 

Figure 7: Pole/Wall mounting plate 

 

 

1.

 

Select the location on the pole to mount the AirHarmony-4000. You can attach the 
AirHarmony-4000 to any pole from 1-7/8 to 16 inches (47.6 to 406.4 mm) in diameter.  

2.

 

Determine where to position the mounting plate on the pole and mark where to drill for 
insertion of the 3/8-16 through-bolt. 

Note:

 Threaded rod and necessary hardware are not supplied by Airspan and are the 

responsibility of the installer. 

 

Summary of Contents for AirHarmony 4000 DC



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands