manualshive.com logo in svg

Airspan 605-0000-742, Hardware Installation

Share
Download
Airspan 605-0000-742 Hardware Installation Download Page 48

605-0000-742_MicroMAX_Hardware_Installation_Rev_G 

44 

 

Note: 

The wire color-coding described in the table is Airspan's standard for wire color-

coding. However, if you implement your company's wire color-coding scheme, ensure that the 

wires are paired and twisted according to pin functions listed in the table above (e.g. Rx+ 

with Rx-). 

 

Note: 

The maximum CAT 5e cable length for ODU/IDU connectivity is 100 meters. 

To connect the BSR to the SDA-4S: 

1.

 

Connect the 15-pin D-type male connector, at one end of the CAT-5e cable, to the BSR's 

15-pin D-type port labeled DATA&PWR&SYNC. 

2.

 

Connect the 15-pin D-type male connector, at the other end of the CAT-5e cable, to the 

SDA-4S's 15-pin D-type port. 

SDA-4S Type II 

Using the SDA-4S Type II 

The SDA-4S Type II (or the SDA-4SDC) provides one to four RJ-45 (100BaseT) ports for 

interfacing with the subscriber's LAN network. 

The ports of the SDA-4S model support Auto Negotiation, allowing automatic configuration for 

the highest possible speed link (10BaseT or 100BaseT), and Full Duplex or Half Duplex mode. 

In other words, the speed of the connected device (e.g. PC) determines the speed at which 
packets are transmitted through the specific port. For example, if the device to which the port 

is connected is running at 100 Mbps, the port connection will transmit packets at 100 Mbps. 

Conversely, if the device to which the port is connected is running at 10 Mbps, the port 

connection will transmit packets at 10 Mbps 

In addition, the SDA-4S ports support MDI/MDI-X automatic crossover, allowing connection to 

straight-through or crossover CAT-5e cables. Therefore, these ports can be connected to either 
a hub (i.e. using crossover cables) or a PC (i.e. using straight-through cables). 

The cable setup for SDA-4S LAN connectivity is as follows: 

 

Cable:

 Straight-through (e.g. when connecting to PC) or crossover (i.e. when connecting to 

a hub) CAT-5e Ethernet cable 

   

Connectors:

 8-pin RJ-45 at both ends 

   

Connector pinouts:

 

o

 

Straight-through cable (e.g. connecting to a PC) 

BSR-to-SDA 

Summary of Contents for 605-0000-742




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands