background image

Page 

2

 of 

14

 

Last One Standing

IMPORTANT 

AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT 

 YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT. 

1. Site survey:

1. Carry out a survey of the area where the Last One Standing will be located, and

check for any overhead/underground cables. It’s important that this is carried out
to  avoid  ground  anchors  penetrating  underground  services,  and  the  Last  One
Standing coming into contact with overhead cables when inflated.

2. You  should  provide  an  adequate power  supply  to  the fan,  this  should  adhere  to

your local power regulations.

3. Check wind speed

:

 It is not allowed to use an inflatable by a higher wind force than

force 5 on the Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh breeze
when small trees in leaf begin to sway.

2. Inflatable Inclusions:

Extra equipment needed in addition to what is supplied with your inflatable: 

Suitable 240v Power Supply to operate the fan

CAUTION!

 

Precautions should be taken during handling and use 

of  the  product  to  prevent  electric  shock.  The  blower  requires  a 

Ground  Fault  Protected  Circuit

  (GFCI).  Please  read  the 

manufacturer’s Instruction Manual before using the blower(s). 

The inflatable 

in its bag 

Anchor Pegs

 

Land Operation 

Manual

 

Repair Kit 

Summary of Contents for Last One Standing















Reviews: