manualshive.com logo in svg

Air Live AIRMAX5, User Manual, Page: 71 / 183

Share
Download
Air Live AIRMAX5 User Manual Download Page 71

4. Web Management-Wireless and WAN Settings 

 

 

AirLive AIRMAX5 User’s Manual 

64

4.2.14 RSSI LED Threshold 

Operation Mode -> Setup -> RSSI LED Threshold

 

The AirMax5 is equipped with 2 LEDs to indicate the signal strength of current connection.   
It is very useful in helping you to align the antenna.  The signal level are classified into 4 
levels, you can change the Thresholds (dividing line) between levels in this setting.  
Please note that the smaller the absolute value of RSSI is, the stronger the signal.    For 
example, -50dB is stronger than -80dB.    RSSI level stronger with -60dB is considered a 
very good connection.    This setting only appears in Client and Bridge modes. 
 

‰

 

No Signal

: When signal strength is less than “Weak Signal Threshold” (i.e. 85dB). 

Both LED are off. 

‰

 

Weak Signa

l: When signal strength is greater or equal than the “Weak Signal 

Threshold” (i.e. -75dB).    Only the Blue LED is on. 

‰

 

Strong Signal

: When signal strength is greater or equal than the “Strong Signal 

Threshold” (i.e. -55dB).    Only the Green LED is on. 

‰

 

Full Signal

: When signal strength is greater or equal than the “Full Signal 

Threshold” (i.e. -45dB).    Both Green and Blue LEDs are on 

 

 

 

Be sure to read 

Chapter 7: Antenna Alignment

 for more information. 

 

 

The RSSI LEDs are working only when the connection is 
established.  Therefore, please make sure all wireless settings are 
correct and the connection is established. 

 
 

4.2.15 Distance 

Operation Mode -> Setup -> Distance

 

Please enter the distance to the remote wireless device here.    The AirMax5 will then 
calculate the appropriate ACK Timeout value automatically.    It is very important that you 
enter the correct distance for long distance connection.    Failure to do so will result in poor 
performance. 

Summary of Contents for AIRMAX5
























































































































































































Reviews:

No comments