manualshive.com logo in svg

Air Live AIRMAX5, User Manual, Page: 17 / 183

Share
Download
Air Live AIRMAX5 User Manual Download Page 17

2. Install the AIRMAX5 

 

AirLive AIRMAX5 User’s Manual 

10

2 

2. 

Installing the AirMax5 

 
This section describes the hardware features and the hardware installation procedure for 
the AIRMAX5.    For software configuration, please go to chapter 3 for more details. 

 

2.1 Before You Start 

It is important to read through this section before you install the AirMax5 

 

„

  The AirMax5 comes with everything you need to start installation with exception 

of the PoE Ethernet Cable.    You can use a good quality CAT-5E outdoor graded 
Ethernet cable (shielded with anti-UV) according to the length you need. 

„

  The AirMax5 must be installed in the upright position if the unit is located in 

outdoor or wet environments. 

 

„

  The use of 5GHz spectrum, Turbo modes, and 5/10MHz channel bandwidth 

might be prohibited in some countries.    Please consult with your country’s 
telecom regulation first. 

„

  You must set the distance parameter to make long distance connection work.   

Please refer to chapter 4 of this user’s guide for details. 

„

  The integrated antenna has forward coverage angle of 30 degree both in vertical 

and horizontal direction.     

„

  The AirMax5 is a 5GHz CPE device only, it can not operate in 2.4GHz. 

„

  If you choose to use the external antenna, please remember to connect the 

external antenna first before power on AirMax5.   

Summary of Contents for AIRMAX5
























































































































































































Reviews:

No comments