manualshive.com logo in svg

Aiphone AN-8000EX, Operating Instructions Manual, Page: 194 / 244

Share
Download
Aiphone AN-8000EX Operating Instructions Manual Download Page 194

6-2

Chapter 6:  SYSTEM SETTINGS USING THE BROWSER

1. OUTLINE OF SETTINGS USING BROWSER

Network settings can be updated and maintenance functions controlled by connecting to the exchange, multi
interface unit, or IP station via the PC's browser*. If an exchange, multi interface unit, or IP station is not within
range for the PC to administrate broadcast communications, use another PC to enable communications with
the exchange, multi interface unit, or IP station.

* Recommended Windows browser: Internet Explorer 6

Notes

• Not all settings can be performed via the browser. After updating the network settings, add the exchange or

multi interface unit manually using a PC installed with the AN-8000 Software, then perform the required
settings. (refer to 

p. 4-12

and 

p. 5-17

.)

• In the factory settings, the same IP address may be duplicated or the PC and the exchange, multi interface

unit, or IP station may not be set to the same network. When using the browser to perform network settings,
either connect only one exchange, multi interface unit, or IP station within the same network or disconnect
the equipment and the PC to be set from the network, and connect them directly using an Ethernet crossing
cable.

• CAUTION: Switching off the power during setting update could cause a system failure.
• Updated settings become valid only after the equipment is restarted. Be sure to restart the equipment if

settings are changed. Conversations and paging currently in progress will be temporarily interrupted while
the equipment restarts.

2. MENU ITEMS

Note

Network Setting (refer to 

p. 6-5

) 

Operation Status (refer to 

p. 6-6

)

Line Status (refer to 

p. 6-12

)

Network Status (refer to 

p. 6-14

)

Operation Log (refer to 

p. 6-15

)

Stream Log (refer to 

p. 6-17

)

System Management (refer to 

p. 6-20

)

Changes the IP address, subnet mask, and 
default gateway of the exchange, multi interface 
unit, or IP station connected to the PC.

Displays the connection status for all exchanges, 
multi interface units, or IP stations within the 
system.

Displays exchange, multi interface unit, or IP 
station operation logs. 

Used to change passwords and handle uploads 
and downloads of settings files.

This menu is used to maintain exchanges, multi 
interface units, or IP stations for which system 
and function settings have been completed by 
means of the AN-8000 software.

Menu

Displays operation status.

Displays a log of the IP network's audio 
communications. 

This setting is applicable to the exchange only. 
Displays the line status.

Summary of Contents for AN-8000EX





















































































































































































































































Reviews:

No comments