AiP ABL-005IR, Manual

Page: 25 / 72

SWIR Line Camera Series User’s Manual
(OM150000013H-EN)
－ 25 －
4-6
Defect Pixel Correction
Defect pixel can be corrected by Defect Pixel Correction
function. The correction is performed by replacing defect
pixel by using adjacent effective pixels. User can activate
this function by set On or Off.
command param1 Description
CL dpc
0=Disable
1=Enable
DPC OFF
DPC ON
GV DefectivePixelCorrection
NOTE
1x3 neighboring pixels are used for correcting a defect
pixel. If there is no effective pixel surrounding defect pixel,
correction is not available.
4-7 LUT
In the camera, there is a luminance value conversion
table which makes the process of gamma correction and
binarization.
In order to enable this function the following commands
are available.
command param1
CL lut-mode
0 ： Disable
1 ： LUT1 Enable
2 ： LUT2 Enable
GV ― ―
NOTE
In case of GigE, programming LUT Selector is done by
UserSet Selector. LUT Selector and UserSet work
correspondingly each other. So, in case of using
UserSet1(UserSet2), LUT1(LUT2) is controllable.
※
UseSet0 is not available for LUT control.
4-7-1
LUT Format
The commands for LUT of γ -correction and binarization is
as below.
command param1 param2 Description
CL lut-format
1
：
LUT1
2
：
LUT2
0 ： Read from flash
１： Linear （ OFF ）
２： Reverse
３： Binarization
４：γ =0.6 Correction
Linear （ OFF/ γ =1 ）
Reverse
Binarization
UserSet
GV LUTFormat
Off
Linear
（ OFF/ γ =1 ）
Reverse
Binarization
― ―
4-7-2
LUT Binarization
The threshold for binarization can be changed.
command param1 param2
CL
binarization/lut-
bin 1 ： LUT1
2 ： LUT2
8bit ： 0 ～ 256
10bit:0 ～ 1024
12bit:0 ～ 4096
14bit:0 ～ 16384
GV LUTThreshold
4-7-3
LUT Setting
The output value from 0~16383 against the input value
from 0 ~ 16383 can be configured.
command param1 param2 param3
CL LUT
1 ： LUT1
2 ： LUT2
Input Output
8bit ： 0 ～ 255
10bit:0 ～ 1023
12bit:0 ～ 4095
14bit:0 ～ 16383
GV
LUTIndex 0 ～ 16383
LUTValue 0 ～ 16383
4-7-4
Save LUT
If LUT is programmed by user’s preference, save LUT data
by the command of LUT-SAVE or UserSetSave.
command param1
CL lut-save
1 ： LUT1
2 ： LUT2
GV UserSetSave
UserSet1
Or UserSet2
4-8
Digital Gain Offset
Digital Gain Offset is the function to re-arrange full scale
by changing black level and by gain setting amplifying
video level as set.
command param1
CL
gain
0 ～ 30 dB
(Range ： 0.01 ～ 31.6 x)
blacklevel
8bit ： -0 ～ 255
10bit:-0 ～ 1023
12bit:-0 ～ 4095
14bit:-0 ～ 16383
GV
Gain
Range ： 0.01 ～ 31.6 x
GainAbs 0 ～ 30 dB *Read only
BlackLevel
8bit ： -0 ～ 255
10bit:-0 ～ 1023
12bit:-0 ～ 4095
14bit:-0 ～ 16383
LUT OFF
16383
16383
Reverse
16383
16383
16383
γ Correction
16383
Binary
16383
16383