manualshive.com logo in svg

Aim-TTI TGR2050 Series, Instruction Manual

Share
Download
Aim-TTI TGR2050 Series Instruction Manual Download Page 39

11 - Digital modulation (Option UO1) 

 

Modulation and Sync outputs 

   

 

38    

 

 TGR2050 Series Instruction Manual 

Modulation and Sync outputs 

The internal modulation signal and the sync signal can both be used as an external 

source, through the MOD IN/ OUT and SYNC OUT connections on the rear panel of 

the instrument. 
 

NOTE 

Modulation must be enabled before the output signal will be available from the rear 

panel.  
 

 

Modulation output (

MOD OUT

) 

The digital signal is encoded and filtered before being used as the modulation 

source. 
 

 

ASK, OOK, MSK, or PSK 

When selected as the modulation type, the options will be

 On

 or 

Off

. To activate the 

modulation output, select the 

Mod. Out 

parameter window, select 

On 

and touch

 

OK

. 

 

 

 

 

Modulating 

Bit Pattern 

Encoded 

Bit Pattern 

Filtered 

Bit Pattern 

Modulating 

Waveform 

Internal 

Modulation 

Generator

Encoding 

Block

Filter Block

Deviation 

Depth

Modulating 

Bit Pattern 

Encoded 

Bit Pattern 

Filtered 

Bit Pattern 

Binary Data 

Encoded Data 

Filtered Data 

Modulating 

Waveform 

Internal 

Modulation 

Generator

Encoding 

Block

Filter Block

Deviation 

Depth

Summary of Contents for TGR2050 Series





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands