background image

9

• Typical Applications....

SWX-200P

High performance zonal music system

TZA-2000

CD Player

Aux Input

'Y' Cord

100V Line
Zone B

Line Output

Zone B

100V Line
Zone A

Line Output

Zone A

SWX-200P

(A)

TZA-2000

Connect the left and right outputs of the CD player 

For providing background music on the other floor, 

to either of the two Aux inputs of Ahuja two zone 

which may have lesser ceiling height, it is 

amplifier TZA-2000 using a 'Y' cord (with two RCA 

recommended to use 12 nos. of Ahuja ceiling 

plugs at one end and a ¼” phone plug on the other 

speakers CS-6081T (at 8 watts tap) connected to 

end).

the 100V output terminal of Zone B of the amplifier
TZA-2000.

A paging microphone can also be connected to 
any one of the mic inputs of the two zone amplifier 

Feed the Line output from Zone B of the amplifier 

TZA-2000 to make announcements.

TZA-2000 to the 1V input of the subwoofer SWX-
200P (subwoofer B), using a patch cord of suitable 

The Mono / Stereo switch of the amplifier 

length with ¼” phone plugs on both ends.

TZA-2000 should be kept in Mono position.

Place the subwoofer 'B' preferably in any corner on 

6 nos. of Ahuja ceiling speakers CS-8151T (at 15 

the floor, with the reflecting port preferably not 

watts tap) can be connected to the 100V output 

facing the corners.

terminal of Zone A of the amplifier TZA-2000.

Set the crossover frequency of each subwoofer to 

Feed the Line output from Zone A of the amplifier 

120Hz and adjust their respective volume controls 

TZA-2000 to the 1V input of the subwoofer SWX-

for optimum performance.

200P (subwoofer A), using a patch cord of suitable 
length with ¼” phone plugs on both ends.

Both the zones of the TZA-2000 have independent 
tone and master controls, which can be adjusted 

Place the subwoofer 'A' preferably in any corner on 

as per system requirements.

the floor, with the reflecting port preferably not 
facing the corners.

This combination of CS-8151Ts and SWX-200P 
(subwoofer A) provides background music for one 
floor.

SWX-200P

(B)

1V Input

Microphone

Mic

Input

1V Input

CS-8151T

Floor 2

Floor 1

CS-6081T

Floor 2

Floor 1

Summary of Contents for SWX-200P













Reviews: