background image

Installation, Operation & Maintenance                                                                         Parksafe Gas Detector 

 

 

Rev: 9   10-20 

3  

 

IMPORTANT SAFETY INSTRUCTIONS 

 

Before any installation, use or maintenance read this manual carefully. 
The information contained within this manual should be referenced for typical installation and operation only.  
For site specific requirements that may deviate from the information in this guide – contact your supplier.  
If this device is used in a manner not specified by the manufacturer, the safety and provided by this device may be impaired. 
This device is designed for indoor operation only. 
The expected lifetime of a NO

gas sensor element is 2 years upon initial power up. The Parksafe control panel will display a message 

to indicate this time and detectors should immediately be replaced. 
The expected lifetime of a CO gas sensor element is 5 years upon initial power up. The Parksafe control panel will display a message 
to indicate this time and detectors should immediately be replaced. 
It is recommended that this device be commissioned upon installation and serviced annually. 
Do not apply lighter gas or other aerosols to the device – this will cause extreme damage. 
High concentrations of alcohol / ethanol found in many products may damage, deteriorate or affect the gas sensing elements – Avoid 
exposure near your device. 
This equipment is designed to detect carbon monoxide and nitrogen dioxide from any source of combustion.  
It is NOT designed to detect smoke, fire or other gases and should NOT be used as such. 
DO NOT remove the gas sensing module when the system is powered up. 
This device provides early warning of the presence of nitrogen dioxide or carbon monoxide, usually before a healthy adult would 
experience symptoms. This early warning is possible provided your alarm is located, installed and maintained as described in this 
guide. 
This device requires a continual supply of electrical power – it will not work without power. 
This device should not be used to substitute proper installation, use and / or maintenance of fuel burning appliances including 
appropriate ventilation and exhaust systems. 
This device does not prevent nitrogen dioxide or carbon monoxide from occurring or accumulating. 
Actuation of your alarm indicates the presence of dangerous levels of NO

2

 or CO.  

Seek fresh air supply and contact your local gas emergency service should you suspect a gas leak. 
This device may not fully safeguard individuals with specific medical conditions.  
If in doubt, consult a doctor / physician. 
Your product should reach you in perfect condition, if you suspect it is damaged, contact your supplier

 

 

 

Manufacturer’s Warranty

 

 

 

Warranty Coverage: The manufacturer warrants to the original consumer purchaser, that this product will be free of defects in 
material and workmanship for a period of two (2) years from date of purchase.  
The manufacturer’s liability hereunder is limited to replacement of the product with repaired product at the discretion of the 
manufacture. This warranty is void if the product has been damaged by accident, unreasonable use, neglect, tampering or other 
causes not arising from defects in material or workmanship.  
This warranty extends to the original consumer purchaser of the product only. 
 
Disclaimers:  Any  implied  warranties  arising  out  of  this  sale,  including  but  not  limited  to  the  implied  warranties  of  description, 
merchantability  and  intended  operational  purpose,  are  limited  in  duration  to  the  above  warranty  period.  In  no  event  shall  the 
manufacturer be liable for loss of use of this product or for any indirect, special, incidental or consequential damages, or  costs, or 
expenses incurred by the consumer or any other user of this product, whether due to a breach of contract, negligence, strict liability 
in  tort  or  otherwise.  The  manufacturer  shall  have  no  liability  for  any  personal  injury,  property  damage  or  any  special,  incidental, 
contingent or consequential damage of any kind resulting from gas leakage, fire or explosion. This warranty does not affect your 
statutory rights. 
 
Performance: During the above warranty period, your product will be replaced with a comparable product if the defective product is 
returned together with proof of purchase date. The replacement product will be in warranty for the remainder of the original warranty 
period or for six months – whichever is the greatest.  
 
 

 
Information on waste disposal for consumers of electrical & electronic equipment.

 

 
When this product has reached the end of its life it must be treated as Waste Electrical & Electronics Equipment (WEEE). Any WEEE 
marked products must not be mixed with general household waste, but kept separate for the treatment, recovery and recycling of the 
materials used. Please contact your supplier or local authority for details of recycling schemes in your area. 

Summary of Contents for PARKSAFE GAS DETECTOR

















Reviews: