manualshive.com logo in svg

Agrident APR250, User Manual, Page: 46 / 49

Share
Download
Agrident APR250 User Manual Download Page 46

APR250 User Manual

 

 

 

24/03/21 

 

 

Page 46 of 49 

While charging

: 

 

▪

 

Be sure to follow the rules listed below while charging the battery. Failure to do so may cause 
the battery to become hot, explode, or ignite and cause serious injury. 

 

•

 

When charging the battery, only use chargers supplied by Agrident.  

•

 

Do not attach the batteries to a power supply plug or directly to a car's cigarette lighter.  

•

 

Do  not  place  the  batteries  in  or  near  fire,  or  into  direct  sunlight.  When  the  battery 
becomes  hot,  the  built-in  safety  equipment  is  activated,  preventing  the  battery  from 
charging  further,  and  heating  the  battery  can  destroy  the  safety  equipment  and  can 
cause additional heating, breaking, or ignition of the battery. 

▪

 

Do not continue charging the battery if it does not recharge within the specified charging time. 
Doing so may cause the battery to become hot, explode, or ignite.  

▪

 

The  temperature  range  over  which  the  battery  can  be  charged  is  0°C  to  45°C.  Charging  the 
battery at temperatures outside of this range may cause the battery to become hot or to break. 
Charging the battery outside of this temperature range may also harm the performance of the 
bat

tery or reduce the battery’s expectancy.  

 
 

When discharging the battery:

  

 

▪

 

Do not discharge the battery using any device except for the specified device. When the battery 
is used in devices aside from the specified device it may damage the performance of the battery 
or reduce its life expectancy, and if the device causes an abnormal current to flow, it may cause 
the battery to become hot, explode, or ignite and cause serious injury.  

▪

 

The temperature range over which the battery can be discharged is -20°C to 60°C. Use of the 
battery outside of this temperature range may damage the performance of the battery or may 
reduce its life expectancy.  

 
 
Disposal considerations:

  

 

▪

 

Observe local, state and federal laws and regulations concerning battery disposal. 

▪

 

Do not disassemble the battery! 

 
 

9  Safety and care 

The  manufacturer  accepts  no  liability  for  damage  resulting  from  improper  use  or  use  not 
consistent with that described in these operating instructions. 
 

▪

  The APR250 Reader contains no parts that can be repaired by the user. For this reason, the 

Reader Electronic may only be repaired by authorized customer service personnel. 

▪

  In both operation and storage of the reader secure to comply with the environment conditions 

specified in the technical data. 

▪

  Clean  the  APR250  Reader  only  with  a  damp  cloth.  Use  only  water  and  any  commercially 

available cleaning agent. 

 
Any modification to the APR250 Reader Electronic will render the warranty null and void. 

 

 

Summary of Contents for APR250


















































Reviews:

No comments