manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 59 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 59

5 Maintenance and Repair 

 

 

Two-wheel tractor 

agria 3600

 

59 

Clutch play 

 

  

Check play "A" at the manual clutch  lever (B/5) 
before each startup. Readjust if necessary (in 
particular during the running-in period after initial 
startup and after the clutch has been replaced). 

  

•

 

Release the locknut. 

•

 

Press and hold the safety lever and adjust 

the Bowden cable adjusting screw 

  until 

play A = 5 – 6 mm is reached. 

•

 

Tighten the locknut to the hand lever bear-
ing. 

  

 

  

Safety circuit 

 

  

Check the function of the safety circuit before 
each startup and during each maintenance work. 

•

 

Traction and PTO shaft drive must stop 
automatically (disengage) and the locking 
strap must engage when you release the 
safety lever (B/1) 

•

 

The clutch must engage when you actuate 
the safety lever (B/1) up to the stop at the 
handle. The clutch must not slip. If neces-
sary, check the Bowden cable and adjust it 

at the Bowden cable adjusting screw 

. 

•

 

Release the locknut. 

•

 

Adjust the adjusting screw as required. 

•

 

Tighten the locknut to the hand lever bear-
ing. 

- agria-Service -

 

  

  

Engine stop circuit 

 

  

Petrol engine  

Check the function of the safety circuit before 
each startup and during each maintenance work. 

•

 

The engine must stop when the stop switch 
is in "OFF" position. 

•

 

Check the electrical cables and connections. 
Replace if necessary.  

- agria-Service -

 

  

  

Summary of Contents for 3600 075













































































Reviews:

No comments