manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 58 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 58

5 Maintenance and Repair 

 

 

58 

Two-wheel tractor 

agria 3600

 

 

  
  

•

 

Check the tyre pressure of the wheels fre-
quently. For smooth driving ensure that the 
tyre pressure in both wheels is the same. 
Never exceed the maximum tyre pressure! 

The max. tyre pressure is shown on the side 
of the tyre. 

 There is a risk of explosion from ex-

cessive tyre pressure.

 

  

  
  

Only skilled specialists are allowed to repair and 
change tyres, using suitable installation tools. 

  

Equipment connection 

 

  

Lubricate the nipples with bio lubricating grease 
after every 

50 

operating hours and after each 

cleaning. 

Grease the end of the PTO shaft before each 
attachment. 

  

Steering bar 

 

  

Lubricate the lubricating nipple with bio lubricat-
ing grease 

yearly

 and after each cleaning with a 

high-pressure cleaner. 

There shall be a grease collar at the point where 
the grease emerges. This protects the bearing 
point against penetrating dirt and water. 

  

Brake 

 

Check operation and function of brake equip-
ment and brake actuation after every 

200

 operat-

ing hours or at least 

yearly

. 

Readjust the brakes at the Bowden cable adjust-
ing screws. 

- agria-Service -

 

  

Summary of Contents for 3600 075













































































Reviews:

No comments