manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 56 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 56

5 Maintenance and Repair 

56 

Two-wheel tractor 

agria 3600

 

•

Remove the 

fan housing 

after every 

100

 

operating hours or 

at least yearly

, ideally 

before the season. Clean the cooling fins on 
cylinder and cylinder head, and the deflector 
plates and the fan wheel that are necessary 
for air circulation.

- agria-Service -

Exhaust system and speed governor 

Regularly check the exhaust system (C/9), gov-
ernor lever, linkage and governor springs for 
soiling and plant debris and clean with a brush or 
compressed air if necessary. 

Danger of fire - 

due to dirty exhaust system!

 

Check before each start-up. 

Replace damaged exhaust parts. 

Handle hot engine components with caution! 

Idle speed 

Always ensure that the engine idle speed is adjusted correctly. With speed regulat-
ing lever at idling, the engine should continue running smoothly. 

- agria-Service -

Engine operating

     

instructions

 

All further maintenance and care of the engine 

 

Summary of Contents for 3600 075













































































Reviews:

No comments