Agria 3600 075 Translation Of The Original Operating Instructions Download Page 40 | Manualshive

Page: 40 / 76

Agria 3600 075 Translation Of The Original Operating Instructions Download Page 40

4 Commissioning and Operation

40

Two-wheel tractor

agria 3600

4 Commissioning and Operation

Commissioning

Petrol engine

Please note that the engine's service life and operational reliability are heavily de-
pendent on the running-in time. Always allow a cold engine to warm up for a few
minutes first of all and do not run up to full power immediately.

During the first

20

hours of operation (running-in period) do not use the engine at

full power.

Attention:

The engine is not filled up with

engine oil for transport reasons!

Fill the engine with engine oil before first
commissioning, but do not go beyond the
maximum level!

Engine operating instructions

This engine runs smoothly with conventional

unleaded regular and premium petrol (also
E10)

as well as

Super plus.

Do not add oil to petrol.

Only use fresh, clean fuel (no older than 3
months) and only use approved fuel cans avail-
able from specialist dealers. Do not use rusted
metal cans or plastic containers which are not
fuel-resistant.

Always consider for good care of the

filter and clean fuel. Use only branded petrol.

Caution is needed when handling fuel.

Petrol is highly flammable and explosive
under certain conditions!

Do not refuel in closed rooms.

Refuel only with the engine switched off and
cooled down.

«
...
38
39
40
41
42
...
»

Summary of Contents for 3600 075













































































Reviews:

No comments