manualshive.com logo in svg

Agilent Technologies U3047AM12, User'S And Service Manual

Share
Download
Agilent Technologies U3047AM12 User'S And Service Manual Download Page 84

78

User’s and Service Guide U3047-90001

U3047AM12

Agilent Support, Services, and Assistance

Agilent Support, Services, and Assistance

Service and Support Options

There are many other repair and calibration options available from the Agilent Technologies support 
organization. These options cover a range of service agreements with varying response times. Contact 
Agilent for additional information on available service agreements for this product. 

Contacting Agilent

Assistance with test and measurements needs and information or finding a local Agilent
office are available on the Web at:

http://www.agilent.com/find/assist

If you do not have access to the Internet, contact your field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by its model 
number and full serial number. With this information, the Agilent representative can 
determine the warranty status of your unit.

Shipping Your Product to Agilent for Service or Repair

IMPORTANT

Agilent Technologies reserves the right to reformat or replace the internal hard disk drive in 
your analyzer as part of its repair. This will erase all user information stored on the hard 
disk. It is imperative, therefore, that you make a backup copy of your critical test data 
located on the analyzer’s hard disk before shipping it to Agilent for repair.

If you wish to send your instrument to Agilent Technologies for service or repair:

•

To improve turn-around time, return your test set along with your network analyzer and cables to 
Agilent so that we may verify the operation of the complete system.

•

Include a complete description of the service requested or of the failure and a description of any failed 
test and any error message.

•

Remove and retain the front handles and all rack mount hardware. The analyzer should be sent to 

Agilent in the same configuration as it was originally shipped.

•

Ship the analyzer using the original or comparable antistatic packaging materials.

•

Contact Agilent for instructions on where to ship your analyzer.

Summary of Contents for U3047AM12





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands