Agilent Technologies U1840A Medalist sj5000 Hardware Manual Download Page 112

Page: 112 / 192

9-2

Agilent U1840A Medalist sj5000 Hardware Manual

Downloading PLC Programs

Downloading Using a USB Cable

If you are using a PC other than the one on the sj5000, it must
have CX-Programmer version 6.1 installed.

The download procedure is as follows:

Connect a USB cable between the PC and the USB port of the
PLC.

Launch CX-Programmer version 6.1.

Click

File

Open

to open c:\cpi\data\PLC\sj5000.cxt.

Click

PLC

Online

The color of the program pane will change from white to
gray. If this does not happen, check the cable.

Click

PLC

Transfer

To PLC

Figure 9-1

CX-Programmer version 6.1 window

Summary of Contents for U1840A Medalist sj5000

































































































































































































Search results

Summary of Contents for U1840A Medalist sj5000

Reviews:

Related manuals for U1840A Medalist sj5000

Brands by name

Popular brands

Agilent Technologies U1840A Medalist sj5000, Hardware Manual

Search results

Summary of Contents for U1840A Medalist sj5000

Reviews:

Related manuals for U1840A Medalist sj5000

Brands by name

Popular brands