Agilent Technologies n5181a Service Manual Download Page 81 | Manualshive

Page: 81 / 202

Agilent Technologies n5181a Service Manual Download Page 81

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting

Troubleshooting Performance Test Problems

1-73

Troubleshooting Adjustment Test Problems (N5183A Only)

The table below shows the assemblies to replace to correct specific adjustment failures. Before you replace an assembly because of an
adjustment failure, perform the following procedure:

1.

Confirm that all self tests passed.

2.

Confirm that all required test equipment is in good operating condition and is correctly connected.

3.

Repeat the adjustment.

•

If the adjustment still fails, replace the first assembly listed in the table for the adjustment that is failing.

4.

Repeat the adjustment.

•

If the adjustment still fails, replace the second assembly listed in the table for the adjustment that is failing.

5.

Chapter 4, "Post-Repair Procedures and Performance Verification"

Automated Performance Test Problems

If the self-tests pass, but an automated performance test fails, use this table to locate the assembly that is most likely to have failed. To avoid
unnecessary reconfiguration of test equipment, run the performance tests in the order in which they are listed in the table. Always use the
latest revision of the service software.

Adjustment that is failing...

Assembly to replace

Microwave multiplier prelevel calibration

A7 Micro Deck

AM calibration

1.

A3 RF Assembly

2.

A7 Micro Deck

Limited absolute power calibration

A7 Micro Deck

ALC mod driver calibration (fails in the low frequency band)

A3 RF Assembly

ALC mod driver calibration (fails in the high frequency band)

A7 Micro Deck

Performance Test that is Failing...

Action to Perform...

(N5161A/81A/62A/82A)

Action to Perform...

(N5183A)

Digital Modulation Power Level
Accuracy Relative to (N5162A/82A
only)

Replace the A3 RF assembly

N/A

Power Level Accuracy

Replace the A3 RF assembly

If a failure occurs at

≥

3.2 GHz, replace the A7

Micro Deck

.

If failure occurs at < 3.2 GHz, replace the A3

RF assembly

Harmonic Spurious

Replace the A3 RF assembly

Replace the A3 RF assembly

Sub-Harmonic Spurious

Replace the A3 RF assembly

Replace the A3 RF assembly

Non-Harmonic Spurious

Replace the A3 RF assembly

Replace the A3 RF assembly

WCDMA Adjacent Channel Power
(N5162A/82A only)

1.

Rerun the test at a power level of

−

7 dBm.

2.

Reduce the power level by 1 dB and repeat test.

3.

Repeat the test three more times, reducing the
power level by 1 dB each time.

•

If the ACP performance improves, replace the
A3 RF assembly.

•

If the ACP performance remains consistent or
degrades, replace the A2 Vector Module.

N/A

FM Deviation Accuracy

Replace the A3 RF assembly

Replace the A3 RF assembly

深圳德标仪器

135-1095-0799

«
...
79
80
81
82
83
...
»

Summary of Contents for n5181a











































































































































































































Reviews:

No comments