background image

   

4

                                                                                                                              

                            

N5101-90001  

System Requirements

PC Requirements

Requirements for all applications:

You must be able to log on to your PC using an account with administrative privileges.

The PC and all signal sources must be connected via LAN or GPIB.

Available PCI slot(s) must meet the 2.2 PCI/ISA (or later) specifications (see the bottom of 

page 13

).

Not all computer cases are PCI or ISA compliant. PCI compliant computer cases accommodate the N5101A PCI 
card with the metal extender, thus enabling both ends to be restrained. For ISA compliant computer cases, an ISA 
retainer (included) must be attached to the N5101A PCI card metal extender to enable the card to fit into the ISA 
slots. To avoid reliability issues, the N5101A PCI card must be restrained on both ends. Refer to 

page 6

 fo

installation instructions.

Application-specific requirements:

Table  2 

N5110A Baseband Studio for Waveform Streaming

Streaming Rate

Slow (

5 MSa/s)

Medium (

20 MSa/s)

Fast (40 MSa/s)

Processor

Pentium

 4, 2 GHz or greater

Pentium 4, 2 GHz or greater

Pentium 4, 2 GHz or greater

Front Side Bus

400 MHz

533 MHz

533 MHz

Memory 
(Size, Type)

512 MB, PC2100

1 GB, PC2700

2 GB, PC2700

Available 
PCI Slots

1: 32 bit/33 MHz and 1 additional 
PCI slot opening

1: 64 bit/66 MHz and 1 additional 
PCI slot opening

1: 64 bit/66 MHz or 1: 64 bit/133 
MHz

a

 and 1 additional PCI slot 

opening

a. Required for the RAID Controller

HDD 
Controller

Generic IDE

Ultra 160 SCSI RAID Controller

Ultra 320 SCSI RAID Controller

Hard Disks

1: Ultra ATA (7200 RPM)

2: Ultra 160 SCSI (10K RPM)

5: Ultra 320 SCSI (15K RPM)

HDD 
Configuration

Single Drive with OS + Data

Dual Drive with OS + Data

Dedicated OS Drive, Data on 
RAID

Operating 
System

Windows

 2000 Professional, 

SP 3

Windows 2000 Professional, SP 3

Windows 2000 Professional, SP 3

Example

HP XW4100

HP XW8000

HP XW8000 w/add-on HDDs

Summary of Contents for N5101A

















Reviews: