29-25
Advanced COMM Trigger Mode and Commands
Use the COMM Trigger Mode to find a serial pattern of bits in a waveform. The
COMM Trigger Mode is primarily used to find an isolated logically one bit in a
waveform for mask testing applications. The pattern is defined by the standards
used by the telecommunication and data communication industries. Mask
testing is used to verify a waveform meets industrial standards which
guarantees that equipment made by different manufacturers will work together.
Set the Mode Before Executing Commands
Before you can execute the :TRIGger:ADVanced:COMMunications
commands, mask testing must be enabled at least one time. The
:MTESt:ENABle command enables or disables mask testing. Then you
can set the mode by entering:
:TRIGger:MODE ADVanced and
:TRIGger:ADVanced:MODE COMM
To query the oscilloscope for the advanced trigger mode, enter:
:TRIGger:ADVanced:MODE?
The :TRIGger:ADVanced:COMM commands define the Communications
Trigger Mode. As described in the following commands, you set up the
:TRIGger:ADVanced:COMM commands with the following commands
and queries.
• BWIDth
• ENCode
• LEVel
• PATTern
• POLarity
• SOURce
Summary of Contents for Infiniium 8000A
