15- 7
External Trigger Commands
PROBe:EADapter
PROBe:EADapter
Command
:EXTernal:PROBe:EADapter {NONE | DIV10 |
DIV20 | DIV100}
The :EXTernal:EADapter command sets the Infiniium external adapter control.
The 1153A, 1154A, and 1159A probes have external adapters that you can
attach to the end of the probe. When you attach one of these adapters, you
should use the EADapter command to set the external adapter control to match
the adapter connected to your probe as follows.
Example
This example sets the external adapter to divide by 10:
10 OUTPUT 707;":EXTERNAL:PROBE:EADAPTER DIV10"
20 END
Parameter
Description
NONE
Use this setting when there is no adapter
connected to the end of your probe.
DIV10
Use this setting when you have a divide by
10 adapter connected to the end of your
probe.
DIV20
Use this setting when you have a divide by
20 adapter connected to the end of your
probe. (1159A probe only)
DIV100
Use this setting when you have a divide by
100 adapter connected to the end of your
probe. (1153A probe only)
This command is only available for the 1153A, 1154A, and 1159A probes. If one of
these probes is not connected to the external trigger you will get a Settings Conflict
error.
Summary of Contents for Infiniium 8000A
