14- 3
Display Commands
CGRade
CGRade
Command
:DISPlay:CGRade {{ON | 1 | CG} | {OFF | 0 | N}}
The :DISPlay:CGRade command sets the color grade persistence on or off.
When in the color grade persistence mode, all waveforms are mapped into a
database and shown with different colors representing varying number of hits
in a pixel. "Connected dots" display mode (:DISPlay:CONNect) is disabled when
the color grade persistence is on.
The oscilloscope has three features that use a specific database. This database
uses a different memory area than the waveform record for each channel. The
three features that use the database are histograms, mask testing, and color
grade persistence. When any one of these three features is turned on, the
oscilloscope starts building the database. The database is the size of the
graticule area and varies in size. Behind each pixel is a 21-bit counter. Each
counter is incremented each time a pixel is hit by data from a channel or
function. The maximum count (saturation) for each counter is 2,097,151. You
can check to see if any of the counters is close to saturation by using the
DISPlay:CGRade:LEVels? query. The color grade persistence uses colors to
represent the number of hits on various areas of the display. The default
color-grade state is off.
Example
This example sets the color grade persistence on.
10 OUTPUT 707;":DISPLAY:CGRADE ON"
20 END
Summary of Contents for Infiniium 8000A
