10-26
Channel Commands
RANGe
RANGe
Command
:CHANnel<N>:RANGe <range_value>
The :CHANnel<N>:RANGe command defines the full-scale vertical axis of the
selected channel. It sets up acquisition and display hardware to display the
waveform at a given range scale. The values represent the full-scale deflection
factor of the vertical axis in volts. These values change as the probe attenuation
factor is changed.
<N>
An integer, 1 - 2, for two channel Infiniium Oscilloscope.
An integer, 1 - 4, for all other Infiniium Oscilloscope models.
<range_value>
A real number for the full-scale voltage of the specified channel number.
Example
This example sets the full-scale range for channel 1 to 500 mV.
10 OUTPUT 707;":CHANNEL1:RANGE 500E-3"
20 END
Query
:CHANnel<N>:RANGe?
The :CHANnel<N>:RANGe? query returns the current full-scale vertical axis
setting for the selected channel.
Returned Format
[:CHANnel<N>:RANGe]<range_value><NL>
Example
This example places the current range value in the number variable, Setting,
then prints the contents of the variable to the computer's screen.
10 OUTPUT 707;":SYSTEM:HEADER OFF”!Response headers off
20 OUTPUT 707;":CHANNEL1:RANGE?"
30 ENTER 707;Setting
40 PRINT Setting
50 END
Summary of Contents for Infiniium 8000A
